Wavetek 39A Spezifikationen Seite 101
- Seite / 137
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
User Manual 301/302
PHASe:STEP POINt | DEGRee
Purpose
This command defines which units will be used when programming the start phase offset between
channels 1 and 2 waveforms.
• <POINt> selects waveform point units
• <DEGRee> selects degree units
PHASe:STEP?
Response to query version
The 302 will return the present POIN, or DEGR depending on the current 302 setting.
PHASe:OFFSet <course_offs>
Purpose
This command programs the start phase offset between channels 1 and 2. Phase may be programmed in
units of degrees, or in units of waveform points, depending on the PHAS:STEP selection. Phase offset
resolution when using this command is 8 points and maximum phase offset is limited by the length of the
waveform.
• <course_offs> numeric value that sets the phase offset between the channels
PHASe:OFFSet?
Response to query version
The 302 will return the present course phase offset value in units of degrees, or units of waveform points,
depending on the PHAS:STEP setting.
PHASe:OFFSet:FINE <fine_offs>
Purpose
This command programs the start phase offset between channels 1 and 2. Phase offset resolution when
using this command is 1 point and maximum phase offset is limited by 128k points.
• <fine _offs> numeric value that sets the phase offset between the channels
PHASe:OFFSet:FINE?
Response
The 302 will return the present fine phase offset value.
VOLTage <ampl> | MINimum | MAXimum
Purpose
This command programs the peak to peak amplitude of the output waveform. The amplitude is calibrated
when the source impedance is 50Ω.
• <amp> numeric value that sets the amplitude
• <MINimum> sets the amplitude to its lowest value
• <MAXimum> sets the amplitude to its highest value
SCPI Command Reference
90
- WARRANTY 3
- Exclusion of Other Warranties 3
- DECLARATION OF CONFORMITY 4
- Model 301 and Model 302 4
- SAFETY PRECAUTIONS 5
- Table of Contents 6
- 301/302 User Manual 10
- Table of Figures 10
- Getting Started 12
- Introduction 13
- Input and Output 16
- Connectors 16
- Operating Modes 17
- Continuous Mode 18
- Triggered Mode 18
- Burst Mode 18
- Gated Mode 18
- Output Type 18
- Standard (Fixed) 19
- Waveforms 19
- Arbitrary (User) 19
- Sequenced 20
- Output State 22
- Front Panel 22
- Indicators 22
- Programming The 22
- Model 301/302 22
- CONFIGURING The INSTRUMENT 23
- Performance 24
- Requirements 24
- Preparation For 26
- Logical Address 26
- Selection 26
- Installation 27
- Bench Operation 27
- Rack Mounting 27
- USING The INSTRUMENT 28
- Power On/Reset 29
- Defaults 29
- Programming the 29
- :VOLTage 2; 30
- ÷ 2) ≤ 5 30
- Controlling the 31
- 301/2 Using 31
- WaveWiz 31
- Controlling 33
- Instrument 33
- Functions 33
- Using the APPLy 33
- Selecting the 36
- Active Channel 36
- Enabling the Main 37
- Selecting an 38
- Selecting a 39
- Standard 39
- Function Shape 39
- Changing the 42
- Frequency and 42
- Sample Clock 42
- External SCLK 43
- Output Amplitude 44
- Filter Type 45
- Operating Mode 46
- Selecting the Trigger 49
- Using the Internal 50
- Trigger Generator 50
- Assigning the 52
- Source For The 52
- SYNC Output 52
- Generating 53
- Arbitrary 53
- What Are 54
- Waveforms? 54
- Arbitrary Memory 55
- Management 55
- Loading Arbitrary 56
- Reversing Byte 58
- Using WaveWiz to 59
- Generate 59
- Using Equation 62
- Editor to Generate 62
- User Manual 301/302 68
- Configuring the Instrument 68
- Fast Binary 72
- Sequence Table 72
- Download 72
- Selecting active 74
- Sequence 74
- Running 75
- Sequences 75
- Using WaveWiz 75
- Advance 77
- Advance Source 78
- Sequences with 79
- Sequences with 80
- Adjusting Phase 84
- Offset Between 84
- Channels 84
- Amplitude 86
- Modulation 86
- System-Related 86
- SCPI Commands 87
- SCPI COMMAND REFERENCE 89
- Query Response 90
- SCPI Command Reference 91
- Subsystem 106
- INSTrument 110
- Trigger 111
- IEEE-STD-488.2 119
- Commands and 119
- Registers 120
- The SCPI Status 120
- The Status Byte 121
- Register (STB) 121
- Generation 122
- Standard Event 124
- Status Register 124
- Status Enable 125
- Register (ESE) 125
- Error Messages 125
- Device-Specific 128
- Commands 128
- Appendix A SPECIFICATIONS 130
- Triangle 131
- Pulse/Ramp 131
- ARBITRARY WAVEFORMS 132
- SEQUENCED SEQUENCES 133
- OUTPUTS (CHANNELS A & B) 134
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern